基于镧锶锰氧化物基阴极的中温固体氧化物燃料电池的性能优化研究

为了提高基于镧锶锰氧化物(LaxSr1-xMnO3,LSM)阴极的中温固体氧化物燃料电池(Solid Oxide Fuel Cell,SOFC)的电化学性能,文章利用CuO清扫Ce0.85Sm0.15O2-δ(SDC)晶界的SiO2杂质以提高SDC的离子电导率,制备了复合电解质材料SDC-CuO,并将SDC-CuO和LSM结合成复合阴极材料,随后分别制备了以LSM和LSM/SDC-CuO作为阴极的SOFC,并研究了这两种SOFC的电化学性能。研究结果表明:在开路电压和工作温度为800℃的条件下,LSM/SDC-CuO基阴极的SOFC的极化电阻为0.14Ω·cm2,明显低于LSM基阴极SOFC的极化电阻(0.36Ω·cm2);LSM/SDC-CuO基阴极的SOFC的最大输出功率密度为237 mW/cm2,显著高于LSM基阴极的SOFC的最大输出功率密度(132 mW/cm2)。     

Effect of high temperature and separated combustion on SO2 release characteristics during coal combustion under O2/CO2 atmosphere

This paper studied the effect of high temperature (up to 1873K) and separated combustion mode (volatile combustion and char combustion are separated) on SO₂ release characteristics during pulverized coal combustion under O₂/CO₂ atmosphere. Coal combustion experiments were conducted at different combustion environment temperatures utilizing a high temperature fixed-bed setup. The results show that as temperature rises, the SO₂ release curve is transformed from a single-peak process to a double-peak process. In separated combustion, temperature has little effect on the volatile-SO₂ (SO₂ released during volatile combustion) but brings about a significant effect on char-SO₂ (SO₂ released during char combustion). Char-SO₂ release amount and the ratio of it to fuel-SO₂ release amount (total SO₂ released during coal combustion) increase with temperature rising. The increase of temperature leads to a dramatic decreasing of sulphur mass fixed in the ash and causes SO₂ release amount to rise when temperature is lower than 1573 K. Separated combustion causes a higher SO₂ release amount than coupled combustion (the same as conventional combustion, volatile combustion and char combustion are simultaneous). Thermochemistry equilibrium composition calculation results show that alkali metals and alkaline-earth metals are significant in sulphur retention. CaSO₄ and Na₂SO₄ are the main sulphates at high temperatures.     

适用于“一步酸溶法”生产氧化铝工艺中稀释料浆的高分子絮凝剂的合成

为达到"一步酸溶法"生产氧化铝工艺中稀释料浆在高温、高酸度工况下进行固液高效分离的目的,以丙烯酰胺(AM)与阳离子(DMDAAC)为共聚单体,通过水溶液聚合法合成了阳离子聚丙烯酰胺(CPAM)絮凝剂。以转化率和相对分子质量为目标,通过单因素分析法确定了最优的合成工艺条件,即反应温度30℃,单体总质量分数为30%,阳离子度5%,K2S2O8和NaHSO3质量分数均为0.005%,2,2′-偶氮二(2-脒基丙烷盐酸盐)(V50)质量分数为0.0025%,乙二胺四乙酸(EDTA)质量分数为0.05%的条件下,反应时间为6 h,获得相对分子质量为1.2×107溶解性能较好的阳离子型聚丙烯酰胺(CPAM)。     

基于STM32的开环霍尔电流传感器的温度补偿研究

研究了一种基于软件补偿结合恒流源补偿的改进温度补偿方法,应用单片机、恒流源、数字温度传感器、乘法器等硬件电路,对传统软件补偿进行了优化,补偿效果较传统恒流源补偿有了明显提升,“温漂”整体下降了约13.7%。在传统的温度补偿方法如热敏元件补偿、恒流源补偿、软件补偿等方式上做了补充,对于霍尔电流传感器精度的提升及实际生产需求的满足有重要意义。     

液压阻尼孔的宽温度范围流动特性试验研究

研制一种适合对各种液压孔口或缝隙进行高低温流体力学试验的新型试验装置，运用该装置对具有不同几何参数的液压阻尼孔进行在-50~80℃宽温度范围内的流动特性试验，研究以普通抗磨液压油HM46和低温抗凝减振器油TITAN SAF 5045为工质及其温度变化时对液压阻尼孔流量-压力特性曲线、幂指数和流量系数的影响，研究表明，在低温条件下，液压阻尼孔的流量系数均因油液黏度增大、流动性变差而呈线性下降的趋势，从宏观上看，HM46通过液压阻尼孔时的流动稳定性较差，其对应流量系数的下降幅度明显大于TITAN SAF 5045对应的下降幅度，厚壁小孔流量系数的下降幅度明显大于薄壁小孔对应的下降幅度。研究所获得的新型试验装置、试验数据分析方法和具体理论公式为深入研究和优化现代液压元件在宽温度范围内的动态性能提供新型试验平台与理论基础。     

近50年大黑河流域气候水文要素变化趋势及突变分析

基于大黑河流域6个气象站1966～2013年气温、降水量、蒸发皿蒸发量、相对湿度和日照时数长期数据系列,采用气候倾向率和滑动t检验法分析了近50年大黑河流域气象要素的变化趋势及变异年份。结果表明,大黑河流域整体呈现暖干气候倾向,气温呈显著增高趋势,变化率为0.43～0.57℃/10a,气温增温变点大致出现了两次,分别在1986、1997年;降水量和蒸发量多呈不显著减少趋势,降水量先减(1981年)后增(1990年),蒸发皿蒸发量先减(1986年)后增(1996年);相对湿度、日照时数多呈显著减小趋势。     

Effect of pyrolysis temperature on the mechanical evolution of SiCf/SiC composites fabricated by PIP

Three types of SiC_f/SiC composites with a four-step three-dimensional SiC fibre preform and pyrocarbon interface fabricated via precursor infiltration and pyrolysis at 1100 °C, 1300 °C, and 1500 °C were heat-treated at 1300 °C under argon atmosphere for 50 h. The effects of the pyrolysis temperature on the microstructural and mechanical properties of the SiC_f/SiC composites were studied. With an increase in the pyrolysis temperature, the SiC crystallite size of the as-fabricated composites increased from 3.4 to 6.4 nm, and the flexural strength decreased from 742 ± 45 to 467 ± 38 MPa. After heat treatment, all the samples exhibited lower mechanical properties, accompanied by grain growth, mass loss, and the formation of open pores. The degree of mechanical degradation decreased with an increase in the pyrolysis temperature. The composites fabricated at 1500 °C exhibited the highest property retention rates with 90% flexural strength and 98% flexural modulus retained. The mechanism of the mechanical evolution after heat treatment was revealed, which suggested that the thermal stability of the mechanical properties is enhanced by the high crystallinity of the SiC matrix after pyrolysis at higher temperatures.     

pH-sensitive self-assembling property of poly(ethyleneimine)/cinnamic acid mixture and its effect on pH-dependent release of monoolein cubic phase

Poly(ethyleneimine) (PEI)/cinnamic acid (CA) mixture was self-assembled into microsphere in aqueous phase. As the pH value increased, the self-assembly became hardly formed. As the molar ratio of the amino group of PEI to the carboxyl group of CA increased, the pH window for the formation of self-assembly became broader. The phase transition temperature of cubic phase was 58.5–67.5°C, depending on the PEI/CA content. The release of dye loaded in cubic phase containing PEI/CA increased in a first-order fashion. The release degree was higher at a lower pH value.     

油封唇口温度变化对密封性能的影响

基于流量因子统计学方法建立油封唇口的混合流体润滑模型,耦合油封的能量守恒方程及黏温方程,通过迭代求解获得油封唇口的温度分布、不同转速下油封唇口的最高温度及温差变化情况;对比分析考虑和不考虑温差情况下油封各项密封性能。结果表明:随着转速的增大,唇口最高温度线性递增,而唇口温差先增大后减小;油封工作时,唇口区域的温度先迅速升高后下降,越靠近唇尖的位置温度越高;与不考虑温度的情况比较,考虑温度变化的影响时密封区域的油膜厚度减小,油膜承载力下降,不利于密封。     

低温贮藏对“翠香”猕猴桃冷害和品质的影响

研究以"翠香"猕猴桃为试材,比较两种温度(0±0.5℃和2±0.5℃)下,贮藏果实的冷害发生情况及品质差异,同时关注果实贮藏期间果实苦味的产生,以期找出果实苦味产生的原因。结果表明,0±0.5℃贮藏时,果实硬度保持较好,果实呼吸强度下降,有冷害和褐变发生,并伴有果实发苦现象;而2±0.5℃贮藏的果实未见冷害和褐变发生,色度得以保持,多酚氧化酶(PPO)和过氧化物酶(POD)活性下降,极显著延缓了细胞膜透性的升高,此外,果实可溶性固形物和维生素C的含量也显著提高,果实没有出现苦味。试验中发现"翠香"猕猴桃苦味现象和冷害伴随产生,并随着冷害发展加重,推测"翠香"果实的苦味可能是由冷害造成的。